Description
RKI’s paper tape monitors utilize highly sensitive colorimetric tapes to achieve interference free gas detection. The FP-330 is equipped with an easily replaceable tape that is highly specific to Formaldehyde. This model is equipped with a digital display showing the type of gas and concentration in PPM. The FP-330 will also display remaining tape life as well as an end of tape alarm.
The FP-330 has audible and visual alarms, as well as alarm relay contacts and 4-20mA output. A unique “Tape Saver mode” extends tape life in applications where high background gas levels may be present.
The FP-330 meets and exceeds OSHA and NIOSH compliance requirements, and does not respond to interfering gases (hydrocarbons, alcohols, solvents, CO, etc.) that may be present in industrial/manufacturing environments. FP 330
Specifications
| Model |
FP-330 HCHO 0 – 0.500 ppm
|
FP-330 HCHO 0 – 1.00 ppm
|
FP-330 HCHO 0 – 5.00 ppm
|
Detection
Principle |
Photoelectric photometry method using tape cassette |
| Detection tape |
Plug in cassette, 65-FCL-018 |
| Detection gas |
Formaldehyde (HCHO) |
| Detection range |
0.030 to
0.500 ppm
|
0.05 to
1.00 ppm
|
0.3 to
5.00 ppm
|
| Alarm point |
1st 0.080ppm
2nd 0.300ppm |
1st 0.17ppm
2nd 0.33ppm |
1st 0.8ppm
2nd 1.7ppm |
Alarm
Operation |
Latching alarm (standard) or non-latching (option)
Lamp: Caution = Yellow
Alarm = Red, with buzzer
|
Zero
Suppression |
0.030 ppm
|
0.05 ppm
|
0.3 ppm
|
| Measuring cycle |
1800 sec.
(30 minutes)
|
600 seconds
(10 minutes)
|
180 seconds
(3 minutes)
|
| Resolution |
0.005ppm
|
0.01 ppm
|
0.1 ppm
|
| Flow rate |
450ml/min. (nominal)
|
Max. tubing
length |
2m (teflon only)
|
| Accuracy |
+/-20% of indication value + 1 digit
|
| Tape operation time |
1 month with no background gas. (see note below)
|
| Alarm Indication |
Warning and alarm with audible and visual indications
|
| Self-diagnosis |
Low flow, tape cut, sensor failure, etc.
|
| External output signal |
4-20mA (load resistance: below 300Ω)
|
| Operating temperature & humidity |
5~35°C 20~60% RH (non condensing)
|
| Gas inlet/outlet |
OD 6mm with fittings
|
| Power supply & power |
100VAC to 220VAC universal power,
+/-10%
|
| Dimensions & weight |
Approx. 6.5″(W) x 7.8″(H) x 10.4″(D)
Approx. 12.125lb
164 (W) x 198 (H) x 263 (D) mm, 6.5kg
approx.
|
When HCHO exists in the background continuously over 0.03 ppm, the tape on FP-330 advances after every measurement, so the tape is consumed very quickly. In this case, to extend operating time, the Tape Saver mode is provided on the FP-330.
Tape Saver mode is available for all three ranges;
0H: Normal operation.
1H: One measurement during one hour. Tape lasts 15 days with constant background level.
2H: One measurement during two hours. Tape lasts 30 days with constant background level.
Specifications subject to change without notice.
